GR shared: How to Make a Wi Fi Booster Using Only a Beer Can

How to Make a Wi Fi Booster Using Only a Beer Can - August 04, 2011 at 08:00AM

Not only is this clever use of a beer can an ultra cheap tech hack, it also means less fiddling around with cardboard and aluminum foil as required by other hack methods. This method has been proven to improve Wi-Fi reception from around 2 bars to about 4 on average, varying between 3 and 5. Give it a go – all you've got to waste is a beer can!

Edit Steps

1. Gather the required materials and tools. These are listed below under "Things You'll Need".
   
   
   

   
   

   
   

   
   

   
   

   
   Gather the required materials and tools.
   
   
   


2. Clean the beer can. Make sure there is no residue left inside.
   
   
   

   
   

   
   

   
   

   
   

   
   Clean the beer can.
   
   
   


3. Take the ring-pull off the can.
   
   
   

   
   

   
   

   
   

   
   

   
   Take the ring-pull off the can.
   
   
   


4. Cut the end off the beer can where there's no opening. Do this using the Stanley knife or similar suitable safety knife.
   
   
   

   
   

   
   

   
   

   
   

   
   Cut the end off the beer can where there's no opening.
   
   
   


5. Cut around the end with the opening almost all the way. Leave a little bit of metal to keep attached the part that will be the base (see the white line in the illustration).
   
   
   

   
   

   
   

   
   

   
   

   
   Cut around the end with the opening almost all the way.
   
   
   


6. Cut along the middle of the can in a straight line, opposite to the piece of metal attaching the base.
   
   
   

   
   

   
   

   
   

   
   

   
   Cut along the middle of the can in a straight line, opposite to the piece of metal attaching the base.
   
   
   


7. Being careful, open up the middle piece of metal by bending it until it vaguely resembles the shape of a radar dish.
   
   
   

   
   

   
   

   
   

   
   

   
   Being careful, open up the middle piece of metal by bending it until it vaguely resembles the shape of a radar dish.
   
   
   


8. Place the completed Wi-Fi booster on your router. Place it so that the antenna pokes through the opening, and stick the base of the can to the router with a small piece of poster tack or other suitable adhesive. It's time to test how much your Wi-Fi is now boosted!
   
   
   

   
   

   
   

   
   

   
   

   
   Place the completed Wi-Fi booster on your router.
   
   
   

Edit Warnings

• Be careful of the sharp edges around the can. It's easy to cut yourself on the sharp metal (and it's a lot worse than a paper cut!).
  

Edit Things You'll Need

• An empty, clean 500ml (16.9 fl oz) beer can
  


• A Stanley knife or similar safety knife
  


• A pair of scissors strong enough to cut through thin metal (most will do it)
  


• A small piece of poster tack or similar adhesive
  

Edit Related wikiHows

• 
  How to Create a New Scope in DHCP
  


• 
  How to Fix the Network in Parallel Desktops
  


• 
  How to Set up Your Laptop to Print Wirelessly
  


• 
  How to See Active Network Connections (Windows)
  


• 
  How to Repair Wi Fi Connection After Windows Service Pack 2 Upgrade
  

Article Tools

• Read on wikiHow


• Email this Article


• Edit


• Discuss

from How to of the Day: http://www.wikihow.com/Make-a-Wi-Fi-Booster-Using-Only-a-Beer-Can Shared by lonelicloud. 评论：